AT89C51RC2-3CSIM【PDF 11/127 页】IC 8051 MCU FLASH 32K 40DIP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3850

7页 8页 9页 10页 [11页]12页 13页 14页 15页

108

AT89C51RB2/RC2

4180E–8051–10/06

Notes:

1. Operating I

CC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 49.), VIL =

VSS + 0.5V,

VIH = VCC - 0.5V; XTAL2 N.C.; EA = RST = Port 0 = VCC. ICC would be slightly higher if a crystal oscillator used (see Figure

46).

2. Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns, VIL = VSS + 0.5V, VIH = VCC -

0.5V; XTAL2 N.C; Port 0 = V

CC; EA = RST = VSS (see Figure 47).

3. Power Down I

CC is measured with all output pins disconnected; EA = VSS, PORT 0 = VCC; XTAL2 NC.; RST = VSS (see Fig-

ure 48).

4. Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLs of ALE and Ports 1

and 3. The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0

transitions during bus operation. In the worst cases (capacitive loading 100pF), the noise pulse on the ALE line may exceed

0.45V with maxi V

OL peak 0.6V. A Schmitt Trigger use is not necessary.

5. Typical are based on a limited number of samples and are not guaranteed. The values listed are at room temperature and

5V.

6. Under steady state (non-transient) conditions, IOL must be externally limited as follows:

Maximum IOL per port pin: 10 mA

Maximum IOL per 8-bit port:

Port 0: 26 mA

Ports 1, 2 and 3: 15 mA

Maximum total IOL for all output pins: 71 mA

If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater

than the listed test conditions.

7. For other values, please contact your sales office.

8. Icc Flash Write operation current while an on-chip flash page write is on going.

9. Flash Retention is guaranteed with the same formula for V

CC Min down to 0.

OH1

Output High Voltage, port 0, ALE, PSEN

VCC - 0.3

VCC - 0.7

VCC - 1.5

VCC = 5V ± 10%

IOH = -200 μA

IOH = -3.2 mA

IOH = -7.0 mA

0.9 VCC

VCC = 2.7V to 5.5V

IOH = -10 μA

RRST

RST Pulldown Resistor

200(5)

250

IIL

Logical 0 Input Current ports 1, 2, 3, 4 and 5

-50

μAV

IN = 0.45V

ILI

Input Leakage Current for P0 only

±10

μA

0.45V < VIN < VCC

ITL

Logical 1 to 0 Transition Current, ports 1, 2, 3, 4

-650

μAV

IN = 2.0V

CIO

Capacitance of I/O Buffer

Fc = 3 MHz

TA = 25

°C

IPD

Power Down Current

100

150

μA4.5V < V

CC < 5.5V

(3)

ICCOP

Power Supply Current on normal mode

0.4 x Frequency (MHz) + 5

VCC = 5.5V

(1)

ICCIDLE

Power Supply Current on idle mode

0.3 x Frequency (MHz) + 5

VCC = 5.5V

(1)

CCProg

Power Supply Current during flash Write / Erase

0.4 x

Frequency

(MHz) + 20

CC = 5.5V

(8)

TA = -40°C to +85°C; VSS = 0V;

VCC =2.7V to 5.5V and F = 0 to 40 MHz (both internal and external code execution)

VCC =4.5V to 5.5V and F = 0 to 60 MHz (internal code execution only) (Continued)

Symbol

Parameter

Min

Typ

Max

Unit

Test Conditions

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式